How To Thread A Husqvarna Viking Sewing Machine Correctly?

Check your sewing machine’s operating handbook for instructions on how to thread the bobbin on a Viking sewing machine. After the bobbin has been returned to its case on older Viking models, the final step of bobbin threading must be performed by hand; however, on modern electronic models, the procedure is complete after the bobbin has been wound and replaced. The bobbin can be threaded in two ways: with the needle already threaded or from the side or back of the sewing machine, but this is true for all models of Viking sewing machines.

Objects That You’ll Use

Bạn đang xem: How To Thread A Husqvarna Viking Sewing Machine Correctly?

• Thread for Sewing
• A Bobbin That’s Empty

How To Thread A Husqvarna Viking Sewing Machine Correctly

Step 1

Remove the bobbin case by pressing the latch and yanking it out of the shuttle’s door. When withdrawing the bobbin, be sure to keep the clasp depressed to prevent it from falling out.

Step 2

Slide the empty bobbin onto the bobbin spindle after releasing the latch and rotating it so that the little round dot faces outward. Disconnect the needle’s thread and feed it through the thread guide at the upper back of the machine to the little discs on the side. Repeat as necessary. The thread can be passed beneath the presser foot and then across the front to the bobbin area on the side if you choose to maintain it threaded while winding the bobbin.

Step 3

Cut the thread after it has been wound several times around the bobbin. Start winding by pressing the foot control. When the bobbin is full, the sewing machine will come to an abrupt halt. Remove it, and then cut the thread that’s attached to it. Set up as many bobbins as you need.

Step 4

A round dot is facing out, so make sure it’s in its proper place in the casing. Pull the thread beneath the tension spring by sliding it into the slot on the bobbin case’s edge. The bobbin should rotate clockwise when the thread is pulled in the direction of the spring in order to avoid unequal tension and thread breaking.

Step 5

Move the thread to the right behind the bobbin case’s hook. Press firmly until it clicks into place before inserting into the sewing machine. Pull the thread end over the cutter, then close the shuttle door and you’re done. Place the top thread under the presser foot and manually move the flywheel to bring up the bobbin thread loop on older model Vikings. To begin sewing, remove 3 to 5 inches of bobbin thread manually from under the presser foot. After shutting the shuttle door on a recent Viking sewing machine, you can begin stitching.

Tip

Before replacing the bobbin, use a tiny brush to remove any lint or threads from the shuttle and bobbin area.

Warning

When threading a bobbin winder, never thread the needle directly. This might cause the needle to flex or break.

How Do You Thread A Husqvarna Viking Jade 20 Sewing Machine?

1. Examine your Husqvarna Viking Jade 20’s documentation.
2. The needle should be at its highest point.
3. Extend the presser foot.
4. When you’re done, screw on the cap and you’re done with your felt pad and spool of thread!
5. Pull the thread between the tension disks after it has passed through the designated guide and slot.
6. In order to get the thread through the take-up lever and into the needle thread guide, you must first guide it down and up via the holes in the manual.
7. It’s faster to use the built-in threader, but make sure the needle and presser foot are properly set before using it.
8. Make sure to pull the needle threader all the way down to get the thread over the hook and under the guide.
9. The hook will drag the thread through the needle, creating a thread loop that you can take out of the needle.
10. The presser foot can then be raised so that the thread can be placed under it.

How Do You Thread A Husqvarna Viking Emerald 116 Sewing Machine?

1. Shut down the Viking Husqvarna Emerald 116.
2. Take a moment to raise the needle and the presser foot, respectively.
3. To get to the take-up lever and needle, pass the thread through the proper guide and slot..
4. Using a needle threader is an option if you want to do so manually.
5. Make sure the needle is raised to its highest point and the threader is lowered as far as possible.
6. In this case, the hook will come from behind the needle eye, and you can bring the thread around and under the hook by wrapping it around the guide.
7. Slowly release the knob while holding the thread.
8. The thread will create a loop in the needle’s eye, which you can then pull to remove it.
9. When you elevate the presser foot, hold the needle thread to bring up the bobbin thread.
10. Using the handwheel, make a full turn toward you.
11. In order to raise the bobbin thread, use the needle thread to pull it up.
12. There should be at least four inches of thread on both sides of the presser foot.

Common Husqvarna Viking Sewing Machine Problems

Even sewing machines like the Husqvarna Viking, which are known for their dependability, can occasionally malfunction. Some of these may be easier for you than others, depending on your previous sewing experience. While operating your Husqvarna Viking sewing machine, here are the eight most common problems you may encounter.

• A bent, damaged, or dull needle or an inappropriate tension might result in missing or loose stitches. This problem can be resolved by replacing the needle and adjusting the top tension.
• When stitching over a pin, button, or zipper, the needle often snaps. A broken needle can also be the result of using the wrong presser foot. To prevent further needle breakage, make sure the needle and needle plate are properly aligned.
• Bobbin tension might get out of whack, causing the handwheel and needle bar to become jammed. Remove the bobbin case and any tangled thread from the machine and rethread it after shutting it off and disconnecting it. To see if the wheel turns, switch it back on!
• This can lead to tangled thread on the underside of your fabric if you use the wrong tension. The machine needs to be rethreaded. This should solve the problem, but if it doesn’t, increase the top tension by one level.
• If your sewing machine won’t start, it’s likely that your power source is malfunctioning. Disconnect the power cord and the foot pedal cord to turn everything off. Afterwards, reconnect the power cords and restart the computer.
• A broken needle thread can be caused by a variety of factors, but tension is the most typical reason. Adjust the top tension to a lower setting after rethreading. When sewing, thread can break due to a variety of factors, including using the wrong side of the needle, using filthy bobbin casings, and using subpar thread.
• Skipped stitches are reversed in the case of puckered stitching. In most cases, it implies that the top tension needs to be adjusted, but a too-large needle can also produce puckering.
• If the touchscreen does not respond, it may be necessary to calibrate the device menu under Settings, or it may require professional service.

How Do You Fill The Bobbin On A Husqvarna Viking Sewing Machine?

1. The Husqvarna Viking sewing machine should be turned off.
2. As much as you can, raise the needle.
3. Remove the bobbin cover by pressing the button.
4. Place the bobbin in its container, making certain that the thread is wound in the opposite direction of the clock.
5. Go into the needle plate’s thread guide by following the arrows and squeezing the thread into its notch, as shown.
6. The surplus thread can be cut with the blade on the right.
7. Send the bobbin cover back.

Is It Worth Repairing a Sewing Machine?

Always consider sewing machine repair in the event that something goes wrong with your sewing machine. Many repairs may be done by you, and even if you hire a professional, it will be less expensive than purchasing a new sewing machine!

Xem thêm : Who Makes Elna Sewing Machines? Everything To Know!

In addition, with careful maintenance, antique sewing machines can last for decades. Depending on the quality of construction, new computerized equipment can last anywhere from five to twenty-five years.

Learning how to perform basic equipment maintenance now will save you money on costly repairs later. Take your car in for an oil change or tire rotation, and you’ll get a lot more mileage out of your vehicle.

A broken needle, tangled tension, loose stitches, or a stuck bobbin are all problems that can be readily fixed.

If your computer’s touchscreen isn’t responding, you may need to consult with a tech expert. You may be able to disassemble the machine’s mechanisms on your own, or you may prefer to have a technician handle that part of the repair.

So, how much sewing machine knowledge do you need to have before you can call yourself an expert? Isn’t it a lot? To get the most out of a sewing machine, you need to know the basics.

As a bonus, you’ll want to have a copy of your sewing machine’s instruction manual on hand for reference. In addition, YouTube lessons can be a useful visual aid for many simple fixes. Here are the most typical fixes for your Husqvarna Viking machine that you may perform yourself.

Viking Sewing Machine Repair

If you’re thinking about fixing your Viking sewing machine, you’ll want to be prepared for some typical mistakes. The location of replacement parts may also play a role in your decision-making. Probably the most crucial thing you’ll need to know is when it’s time to call in the experts!

How Do I Fix the Tension On My Husqvarna Sewing Machine?

Skipped stitches and thread nests can be avoided by learning how to change the tension on your Viking sewing machine. “How do I adjust the tension?” is one of the most often asked questions about most sewing machines.

In order for thread tension to work, the thread spool and the bobbin must exert a specific amount of force, or strength. The tension mechanisms operate independently of each other. The top tension is frequently adjusted, but the bobbin tension rarely needs to be tinkered with.

You need to make a tension adjustment if your stitches don’t appear to be flat and even on both sides of the fabric. Depending on the type of fabric, you may need to apply a varied level of tension.

A high-end sewing machine with automated tension adjustment is the lone exception to this rule!

You can now adjust the tension on select new Viking models with a touch screen. The tension can also be adjusted using a dial on some versions.

In order to create more tension in your stitches, you need adjust your sewing machine’s tension to a higher level. Similarly, lower stitch tension readings indicate less stitching tension.

Using contrasting colors of thread in your bobbin and thread spool allows you to readily test the tension. Make sure none of the threads puckers or skips stitches or knots while you sew.

Foot Pedal Not Working

It’s a good idea to check the foot pedal connection first if you press the foot pedal and nothing happens. Unplugging and replugging the connection to the foot pedal may not solve the problem, so seek for a loose wire.

Xem thêm : How To Sew A Flanged Pillow Sham With Mitered Corners? Complete Step-by-Step Guide

The plastic foot pedal case can be opened up to check for damaged or loose wires if you’re feeling bold. Inside, something may have shifted.

You may need a new foot pedal if this doesn’t work. The good news is that you can usually find these at a discount! There are a few things you should keep in mind while purchasing a pedal.

Feed Dogs Stuck Down Position

Your sewing machine will grind to a halt if the feed dogs get stuck.

There are small fangs in the needle plate’s centre that look like feed dog teeth. You can keep the fabric moving under the needle as you sew thanks to these miniature treadmills. Obviously, this means that when your feed dogs get stuck, things go awry!

Lint or thread jamming the feed dogs is the most common cause of this problem. It’s unlikely that this will occur if you maintain your machine properly.

Rethreading your machine in case the feed dogs get stuck due to incorrect threading is always a good idea.

What to Do If Your Viking Sewing Machine Jams Up

Your sewing machine may need to be rethreaded or disassembled if the handwheel won’t turn at all and you can’t get it to start up again.

Remove the fabric from under the presser foot to see if that helps. The scissors may be needed for this. Rethread everything after that. More often than you might believe, rethreading fixes jams!

Steps to follow if that doesn’t work:

1. Make sure your sewing machine’s power cord is properly connected to a wall socket and your sewing machine.
2. Switching on and off the machine might help.
3. Make that the foot pedal is securely connected to the machine and that no cables are hanging free.
4. Make sure there are no tangles in the bobbin case stopping the bobbin from turning.
5. It’s safe to clean and lubricate the hook if your manual recommends it.
6. Make sure everything is back in place before turning the handwheel to see if the bobbin moves!

Husqvarna Viking Dealers Near Me

In order to purchase a Viking machine or to obtain the services of a Viking-certified technician, you must locate a dealer or shop in your area. Googling is usually the best way to find a legitimate online or brick-and-mortar retailer. The official Husqvarna store locator can be found on the company’s website.

You can, of course, take your machine to a small-town repair shop and cross your fingers. Even if your equipment is out of warranty, you should insist that the technician be Viking-certified if you want a guarantee of success.

Because sewing machine repair involves extensive education and certification, you should budget accordingly. For example, a simple tune-up can cost as little as $100. Some professionals, like automotive mechanics, charge by the hour plus the cost of the parts. Others may charge based on the nature of the repair.

When you go to a repair business, bring your machine, the power cord, the foot pedal, and the basic zigzag foot.

Conclusion

There you have it! Before we get into the specifics, let’s quickly review how to thread a Husqvarna Viking sewing machine. You’ll start by elevating the needle and presser foot. From there, you’ll guide the thread and adjust tension. If you’d like to learn more about how to set up a sewing machine, please check out our tutorial.

Nguồn: https://spasifikmag.com
Danh mục: Sewing Tips